Replacing Lock on uPVC Door
If you are looking to replace the lock on your upvc door it is necessary to take off the handle and screw holes. This is usually easy to accomplish.
The next step is to find the screw which holds the lock barrel in place. It is typically a different color than the other screws and located on the outside of the faceplate.
Remove the Cylinder
To change the lock on your doors made of upvc first, you need to remove the existing cylinder. This is a simple process that can take about 30 minutes. All you need is a small screwdriver. You'll need to locate the Euro cylinder fixing screw, which is usually found on the inside of the door, just next to the lock cylinder. The screw must be easily identified as it is usually different in colour from the rest of them. Remove this screw and store it in a safe place.
After the cylinder has been removed, you can start working on removing the handle. To do this, simply open the door to allow full access to the inside edging of the door and the side of the faceplate of the lock.
Begin by using a screwdriver to remove the screw that connects the handle to the door. Once the screw has been removed, you can pull the handle towards you and the rest out of the door.
If you have trouble getting the handle off, you may need to remove the screw that holds it to the stud of the door frame. You can use a screwdriver or drill to remove the handle. Be careful not to strip or cross-thread it.
If you are about to replace your cylinder, ensure that it is the right size for the door you have. Cylinders are measured according to two measurement points: (a) the distance from the centre of the Fixing Screw hole to the bottom of the cylinder, and (b) the distance between the keyhole and the edge of the lock plate.
Remove the Handle
The good news is, when your upvc handle gets stiff, floppy, or loose, it's an easy issue to solve. The multipoint lock cylinder, or other internal parts within the door, in between the handle and the frame, are typically the cause. It is not uncommon for Upvc locks to wear out due to weather conditions, heavy usage or simply ageing and this will often lead to problems with the locking mechanism or closing mechanism of the door.
If the cylinder has been damaged, it can be difficult to turn the key, and the lock can become stiff, which can cause the handle to droop. The cylinder is easily replaced, and it is a simple process. It is possible to complete this yourself, though some understanding of how the mechanism works will be required. The first step is to unhook the handle which will permit you to get access to the valve and replace it with a new one.
You will require an electric screwdriver and measuring tape for this. You must determine the dimensions of your current cylinder since it will assist you to order the correct replacement. The cylinder is the element that locks your upvc door, and it is important that you ensure that you get the exact size.
To take off the old cylinder, it is need to unscrew the screws that secure it. Be careful not to strip out the screws, as this could make it difficult to remove the screws in the future. After the screws have been removed the cylinder will pop out easily.
Take off the Lock Barrel
Upvc is a strong material and designed to keep you and your family safe. They are available in various styles and colours to suit any style. These doors are also thermally efficient and maintenance-free. They are not without disadvantages. The locking point, or barrel lock, may get faulty in time and requires to be replaced. It is a simple procedure, but you should be aware of a few things before you begin.
To remove the screw that is holding the lock cylinder, you will need to remove your door handle. It's typically a different color from the other screws and can be found on the edge of the door, close to where the keyhole is located. Remove the screw and place it in a safe location. Then, carefully slide out the outside and inside door handles. Be sure you do this slowly and not too fast, as it may harm your uPVC door.
After you have removed the handles, use a screwdriver to disconnect the screws that are holding them to the door frame. This will let you better access the pins that keep the cylinder in position. You can then try to pull and wiggle the cylinder in order to see if this will loosen it. If it does move it toward you, and then pull it out of the socket.
After you have removed the old lock cylinder it is important to replace with a new one which has anti-snap protection and anti-bump. You can do this yourself if have the tools you need, or you can hire an expert locksmith to do it for you. This is an easy job that should take no more than five minutes.
Install the New Cylinder
A upvc door lock can be broken or damaged in a variety of ways. For example, a tenant may have moved out and not returned the key, or the cylinder may have become damaged and no longer works as it should. It is essential to select the right size replacement for your door's upvc lock. double glazed window lock repairs is because if the incorrect one is installed it could result in your door being susceptible to a method known as "lock snapping" which is the cause of 25 per cent of burglaries.
It is crucial to choose the proper cylinder. The procedure is simple and takes only five minutes. You will need a screwdriver to take off the screws that attach to the faceplate on the handle and the cylinder, but once this is done, it is a simple task to replace them.
Be sure to open the handle and gain access to the lock cylinder located on the other side of the faceplate of the handle. This will ensure that you are able to easily disconnect the lock cylinder, without needing to move the door handle and expose any internal parts of the handle frame.
The next step is to take the old cylinder out and measure it, you must know the overall length and the diameter of the cam, which rotates to lock and unlock the door. This will enable you to find a new cylinder that is similar or smaller. This is the most crucial part of the whole procedure. The cylinder should be flush with the handle and should not extend more than 5mm away from it.
Install the Handle
It is not uncommon for a door lock made from upvc to jam and this can be caused by something breaking inside the case that controls the bolts that retract into the strike or keep plate. Most often, this can be resolved by making an Allan key adjustment beneath the hinges of the door however occasionally this could put excessive pressure on parts of the central case, so it is best to call a professional out.
It is important to have quick and simple access to both sides when you are changing the handle. Also, it is crucial to use the right tools. It is recommended to place the door on its side to ensure that it doesn't close during this process.
The first step is to loosen the screws that keep the handle together using a screwdriver. Once the screws have been loosen you can take off the handle. Once the handle and cylinder are removed, it's time to put in the new handle. Make sure that the new handle is the right size for your existing cylinder and hole center. To determine the proper size you need to measure the length of the spindle on the lever that you currently have. Also ensure that the screw fix centres on the handle are the same as the screw fixing centres on your current cylinder and hole centre.
Replacement handles from Fab & Fixed are available in various styles and are built to last. They are perfect for people who want to upgrade their Upvc handles and increase their home security. The correct handle will make your home safe and secure, as well as making it difficult for burglars to break into.